15 49.0138 8.38624 1 0 4000 1 https://eatgreenpoint.com 300 0
theme-sticky-logo-alt
theme-logo-alt

How to clean carbon deposits from an iron: 7 ways

How to clean carbon deposits from an iron: 7 ways

Over time, any housewife is faced with the problem of carbon deposits on the iron. And no matter what modern bells and whistles your electrical appliance boasts, it can easily be comprehended by this “ailment”. But don’t despair! Many years of folk experience has collected a lot of ways with which you can eliminate unacceptable contamination of the iron, and in our article we will talk about them in more detail..

1. We clean the iron with salt

The most affordable way is to clean the iron from carbon deposits using salt. To do this, you can use simple table salt, preferably larger. Better yet, take sea salt for cleaning. To achieve the best effect, the iron must be heated. Next, we act in one of three ways:

1. The iron must be slightly heated and turned off. Sprinkle the surface of its sole with salt and three damp rags until the carbon deposits disappear. At the end of the procedure, the surface must be wiped with a dry cloth. During cleaning, you must act very carefully so that the salt crystals do not get into the steam outlet holes..

2. Turn on the iron and set the most gentle mode on the regulator with a lower degree of heating. Then, in cheesecloth or a thin rag folded in half, pour salt and in such a kind of compress, three surfaces. Using this method, you can clean up simple dirt.

3. The device must be properly heated. While it is gaining temperature, put thick cardboard on the ironing board, pour salt on it. Then, with a heated base, we pass through the salt grits in a circular motion, until the dirt is cleaned.

Nowadays, there are many new electrical appliances, and salt may not be suitable for every coating. For example, irons with a Teflon surface cannot be cleaned with it..

How to clean the iron from carbon deposits - Clean the iron with salt How to clean the iron from carbon deposits - Clean the iron with salt How to clean the iron from carbon deposits - Clean the iron with salt

2. Application of vinegar

Another simple method that does not require special material costs is to remove carbon deposits from the iron with vinegar. If you are trying to keep an eye on your favorite electrical appliance, then small soot spots can be easily removed by soaking a cotton swab or cloth in vinegar. By the way, do not forget about the holes for the steam outlet – they can also be cleaned with vinegar using a cotton swab for the ears. After such cleaning, the soleplate of the iron must be wiped dry..

If vinegar cannot cope with plaque on its own, add ammonia to it, but note that the device must be absolutely cold.

Often, hostesses pay attention to carbon deposits only when it becomes completely impossible to iron and it is rather difficult to eliminate such contamination. In this case, vinegar can also save the situation: you need to thoroughly moisten a cloth with it in the evening and put an iron on top, leave it in this position until morning. In most cases, even significant plaque softens and peels off easily during this time. Please note that vinegar has a rather pungent smell, so do not leave such a “composition” in the living area – it must be isolated (for example, taken out to the balcony).

How to remove carbon deposits from an iron - Applying vinegar How to remove carbon deposits from an iron - Applying vinegar How to remove carbon deposits from an iron - Applying vinegar

3. Cleaning the iron with salt and vinegar

The best cleaning results can be obtained by combining salt and vinegar. These two components must be mixed in a small saucepan and put on fire, stirring until the salt is completely dissolved. In this case, it is important not to bring the solution to a boil. The finished solution needs to be cooled a little so as not to burn yourself, then moisten a cloth in it and rub the contaminated areas thoroughly. In difficult cases, you can use a soft-bristled brush (you cannot use a metal one). Next, you need to wipe the surface with a dry cloth, heat the iron and iron any old cloth with it. According to the hostesses, although the smell of this homemade cleaning solution is not very good, its cleaning properties are excellent..

How to remove carbon deposits from the iron - Cleaning the iron with salt and vinegar

4. Removing carbon deposits with soda

The cleaning abilities of soda have been known to housewives for a long time. Often it is used to clean especially complex contaminants on dishes, plumbing, and is used in digestion. Actually, why not clean the iron with it? You can take baking soda or soda ash, while the work should be carried out with rubber gloves, since the soda composition can irritate the skin. Soda must be mixed with a little water until a homogeneous paste is obtained. We collect the composition on a rag or brush and three on the sole of our iron, making sure that the paste does not fall into the holes. When the surface is completely cleaned, it must be wiped with a dry cloth.

How to remove carbon deposits from an iron - Removing carbon deposits with baking soda

5. Use of liquid chemicals

The surface of the iron can be restored to its proper condition using fairly corrosive liquids, which include nail polish remover and acetone. They cope especially well with carbon deposits from polyethylene or synthetic fabrics. It is enough to moisten the cloth with the solution and wipe off the dirt. Work must be carried out with gloves. It is worth considering that liquids emit a rather pungent odor, so it is advisable to use them in a well-ventilated area. If you absolutely hate such “aromas”, you can use hydrogen peroxide. It is odorless – just moisten a cloth with it and rub the stains.

How to clean carbon deposits from an iron - Using liquid chemicals

6. Paraffin candle

One of the most “ancient” methods that our great-grandmothers used was the use of a paraffin candle to remove carbon deposits from the iron. In advance, you need to thoroughly warm up the electrical appliance and prepare a tray onto which droplets of hot wax will drip.

So, we wrap the candle in a dense cloth (it is better to use cotton) and wipe off the carbon deposits. The iron must be kept tilted so that the wax can drain freely and not get into the steam holes. Otherwise, frozen in these holes, it will warm up during the next ironing and stain clothes. At the end of the procedure, wipe the surface clean with a dry cloth.

How to remove carbon deposits from the iron - Paraffin candle

7. Special pencil for cleaning the iron

If you are not a supporter of folk methods of dealing with carbon deposits on the iron, or if they turned out to be powerless, you can purchase a special chemical pencil designed for these purposes. The iron must be turned on and thoroughly warmed up. Next, we rub the surface with a pencil and turn off the appliance.

The chemical cleaning process will start soon – the carbon deposits will begin to flake off. You need to take a soft cloth and wipe off the softened dirt deposit. Then the base is wiped with a damp cloth. In the process, an unpleasant odor may appear, which should not be feared – this is just the evaporation of ammonia, which is part of the pencil.

How to remove carbon deposits from the iron - Special pencil for cleaning the iron

Previous Post
De werkmuur in de keuken afwerken (80 foto’s)
Next Post
Toiletdesign i Khrushchev (80 billeder)